Mon–Fri, 8 AM–4 PM · Emergency electrical service
Neatly wired residential panel with every circuit hand-labeled, wired by River City Electric

A guide for Chattanooga Tesla owners

Planning a Tesla Wall Connector at home.

What to settle before install day: panel capacity, circuit size, where the charger goes, two-car households, and permits, from a certified Tesla installer.

5.0 from 20 Google reviews · Certified Tesla installer · TN license #75272 · GA license #EN218035

The short version

The charger is the easy part. The panel decides the rest.

Hanging a Wall Connector takes very little time. What decides how fast it charges, and whether it runs trouble-free for years, is the electrical work behind it: how much room your panel and service have, the size of the dedicated circuit, and how the wire gets from the panel to the garage.

River City Electric is a certified Tesla installer and a licensed electrical contractor in Tennessee and Georgia, so the load check, the circuit, and the install are handled by one team.

  • 01

    Full speed

    A dedicated 60-amp, 240-volt circuit lets the Wall Connector deliver up to 48 amps.

  • 02

    Right-sized

    When the panel is tight, a smaller circuit still charges overnight for most daily driving.

  • 03

    Room to grow

    A panel upgrade or load management makes room for a second car, a generator, or new loads.

Decisions, in order

Five things to settle before install day.

  1. 01

    Load check

    We look at your panel, your service size, and what the house already draws, including HVAC, ovens, and dryers.

  2. 02

    Circuit size

    Full-speed 60 amps where there is room, or a smaller circuit set to match, so the breaker never runs past its rating.

  3. 03

    Location

    Garage wall or exterior, placed so the cable reaches the charge port and the wire run stays short and protected.

  4. 04

    One car or two

    Two Wall Connectors can share one circuit with power sharing, or each can get its own when the panel allows.

  5. 05

    Permit & walkthrough

    Permit and inspection where required, then we confirm it charges and connect it to your Wi-Fi for updates.

Building or remodeling?

Make the garage EV-ready before drywall.

Running the circuit and reserving panel space at rough-in costs far less than opening finished walls later. Builders and designers can see our pre-wire checklist.

  • Panel space

    Reserve capacity for one or two charger circuits in the panel schedule.

  • Backup power

    Decide how the charger behaves on a standby generator so it doesn’t overload the unit during an outage.

  • Garage lighting

    Plan garage, driveway, and exterior lighting in the same scope.

Questions

Home Tesla charging, in plain English.

What size circuit does a Tesla Wall Connector need?

For full speed, a Wall Connector is typically installed on a dedicated 60-amp, 240-volt circuit, which allows up to 48 amps of charging. It can also be set up on a smaller circuit at a lower charging speed when the panel doesn’t have room for 60 amps. We size it after a load check of your panel and service.

Do I need a panel upgrade for a Tesla charger?

Not always. Many panels have room for a dedicated charger circuit. If a load calculation shows yours doesn’t, we explain the options, including a smaller circuit, load management, or a panel upgrade, before any work begins.

Wall Connector or a 240-volt outlet?

A 240-volt outlet with Tesla’s Mobile Connector works, but it charges more slowly than a Wall Connector. A hardwired Wall Connector is the cleaner long-term choice for most garages, and it can receive firmware updates over Wi-Fi.

We have two Teslas. Do we need two circuits?

Not necessarily. Tesla Wall Connectors support power sharing, so two units can split the power available on one circuit. We look at your panel and how you drive to decide whether one shared circuit or two separate circuits makes more sense.

Can the charger go outside?

Yes. The Wall Connector is rated for indoor and outdoor use. We plan the location so the cable reaches the charge port comfortably and the wire run from the panel stays tidy and protected.

Does a home charger installation need a permit?

A new 240-volt charger circuit generally needs a licensed electrician and, where the city or county requires it, a permit and inspection. We handle that as part of the job in Tennessee and Georgia.

Who do I call if something needs attention later?

Service after the sale: call 423-718-7085, Mon–Fri, 8 AM–4 PM, and you reach the team that installed your charger.

See how we install them on our Tesla charger installation page, or read about panel upgrades.

Start your project

Get a Tesla charger estimate.

Call River City Electric or send a few details about your panel and garage. Planned charger installs include a free estimate across Chattanooga and North Georgia.

david@rivercityelec.comOffice hours: Mon–Fri, 8 AM–4 PM

Call (423) 718-7085 Free Estimate